# Brake Fluid Reservoir Replacement in Upland > Cracked brake fluid reservoir, leaking grommets or a faulty level sensor? We replace the reservoir in Upland and bleed the system. Estimate first. Source: https://route66autorepairshop.com/brake-services/brake-fluid-reservoir-replacement Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** A **cracked reservoir** or tired **grommets** can leak or let air in. We pinpoint the failed piece, replace it, and bleed the system if air got in. The brake fluid reservoir is the plastic tank on top of the master cylinder that holds reserve fluid and often carries the low-level sensor. Route 66 Auto Repair in Upland replaces reservoirs that crack, leak at their rubber grommets, or trigger false warning lights. Years of engine heat make the plastic brittle, and a cracked tank lets moisture in, which shortens the life of the fluid between each [brake fluid flush](https://route66autorepairshop.com/brake-services/brake-fluid-flush). We confirm whether the problem is the tank, the grommets, the cap or the sensor, and put the answer in a written estimate. ## What are the signs of a bad brake fluid reservoir? - Wet fluid at the base of the tank where it meets the master cylinder - Hairline cracks or a cloudy, yellowed tank you can no longer read - A brake warning light that flickers with a full reservoir - A cap that will not seal or has a torn diaphragm - Broken mounting tabs that let the tank rock ## Is it the tank, the grommets or the sensor? The reservoir usually presses into the master cylinder through two rubber grommets. When those harden, fluid seeps at the joint while the tank itself is fine. New grommets may be all that is needed. A warning light with a full tank points to the level sensor or its connector. On some vehicles the sensor is part of the tank, so a sensor failure means a new reservoir. We test it before quoting. If fluid is truly low, we trace that first with [brake fluid leak detection](https://route66autorepairshop.com/brake-services/brake-fluid-leak-detection). ## Our reservoir replacement process 1. **Confirm the failure:** We check for cracks, grommet seep and sensor function with a meter. 2. **Remove old fluid:** Fluid is drawn from the tank before it is unclipped, so the master cylinder is not left open for long. 3. **Fit new parts:** The new reservoir and grommets are seated, and the sensor connector is cleaned and checked. 4. **Bleed if needed:** If air entered the master cylinder, we bleed the system and check pedal feel on a road test. ## What's included - Crack, grommet and cap inspection - Level sensor and connector test - New reservoir or grommets as quoted - Fresh fluid of the specified type - Bleed when air has entered the master cylinder - Warning light and pedal check with a road test ## Need-now or need-later? **Need now:** - An active leak from the tank or grommets - A cap that no longer seals, letting dirt and moisture in **Need later:** - A faded tank that still seals and reads with a flashlight - A cosmetic crack in a mounting tab with the tank held firmly ## How pricing and timing work Grommets alone are a small job. A full reservoir costs more, and on some engines access takes extra time. If air got into the [master cylinder](https://route66autorepairshop.com/brake-services/brake-master-cylinder-repair), bleeding is added and listed on the estimate. AAA members get 10% off parts and labor, up to $75. This is usually same-day work when the board allows; call before you drive over. ## Aftercare Keep the level between the marks and do not overfill; the fluid needs room to expand in summer heat. If the warning light returns, come back and it goes to the front of the line. ## Frequently asked questions ### Can I glue a cracked brake reservoir? We do not recommend it. Brake fluid attacks many adhesives, and the tank flexes with heat. A patch that holds on the driveway can let go on a hot afternoon. A new reservoir is the reliable fix. ### Why is my brake light on when the reservoir is full? The float or switch inside the level sensor may be stuck, or the connector may be corroded. The parking brake switch can also light the same lamp. We check each before recommending a part. ### Do I need a full brake bleed after replacing the reservoir? Only if air got into the master cylinder. If the ports stayed full during the swap, a bleed may not be needed. We test pedal feel and tell you which applied to your car. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.