# Coolant System Flush Valve Repair in Upland > Leaking flush tee or block drain in the cooling system? Route 66 Auto Repair in Upland repairs or removes old flush fittings and restores the original hose. Source: https://route66autorepairshop.com/cooling-heating-ac-services/coolant-system-flush-valve-repair Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** A leaking **flush tee** is usually an add-on from a past DIY service. We often remove it and restore a **one-piece hose** rather than patch it. Most cars do not come with a flush valve. What people call one is usually a plastic flush tee spliced into a heater hose by a past owner, or a block drain cock threaded into the side of the engine. Route 66 Auto Repair in Upland finds which one is leaking, then either replaces it or removes the tee and restores a proper one-piece hose, with the choice written on your estimate. ## What counts as a coolant flush valve? - A plastic flush tee with a cap, cut into the heater hose for garden-hose flushing - A block drain cock or plug on the side of the engine - A drain or bleed valve built into a coolant pipe on some engines - A quick-connect service port used by some shops for exchange machines ## Why do flush fittings leak? Flush tees are made of plastic and sit in a hot, pressurized hose. Over time the plastic turns brittle, the cap gasket dries out, and the two hose clamps holding the tee loosen. A crack can open with no warning, and it often happens on a hot day when pressure is highest. Many tees were installed years ago and forgotten. Block drain plugs are metal and rarely fail on their own. They leak when the threads corrode or when a plug was reinstalled without sealant where the design calls for it. Because they sit low on the engine, the leak can look like a [coolant leak](https://route66autorepairshop.com/cooling-heating-ac-services/coolant-leak-repair) from somewhere much bigger. ## Our flush valve repair process 1. **Identify the fitting:** We trace the leak under pressure and confirm whether it is an add-on tee, a block drain or a factory valve. 2. **Recommend a fix:** The estimate explains the options: replace the fitting, or remove an add-on tee and install a new hose section. 3. **Repair:** Coolant is drained to below the fitting, and the part is replaced or the hose is restored with new clamps. 4. **Refill and test:** The coolant your engine specifies is refilled, air is purged, and the repair is pressure tested. ## What's included in flush valve repair - Pressure test to locate the leaking fitting - Replacement fitting, plug or new hose section as approved - New clamps at every disturbed joint - Coolant drain, refill and air purge - Leak check at operating temperature ## How urgent is a flush fitting leak? **Need now:** - A cracked flush tee or a missing cap - Coolant spraying from the heater hose area - A block drain dripping steadily **Need later:** - An old tee that is dry but brittle-looking - Light crust around a block drain with no level loss ## How pricing and timing work A tee near the top of the engine is quick to reach. Block drains on some V6 and V8 engines sit behind the exhaust manifold or starter, which adds time. Removing a tee may mean a new molded heater hose instead of a straight piece, and the estimate shows which. The diagnostic fee is stated at the counter before testing and applies to approved related repair. Many of these finish the same day when the board allows. ## After the repair Keep an eye on the reservoir for a few cold mornings. If you had the tee removed, future coolant changes are done by draining and refilling or with a proper [cooling system flush](https://route66autorepairshop.com/cooling-heating-ac-services/cooling-system-flush) instead of a garden hose, which also keeps tap water minerals out of the system. ## Frequently asked questions ### Is it bad to flush with a garden hose? Tap water carries minerals that can leave deposits, and it dilutes the coolant mix unless the system is fully drained afterward. A controlled drain and refill with the correct coolant is the cleaner method. ### Why remove the tee instead of replacing it? It is one more plastic joint in a hot hose. If you do not plan to flush at home, a one-piece hose has fewer places to fail. ### Does my car have a block drain? Many engines do, some do not. We check your engine's layout during the inspection and tell you what is there. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.