# Cooling System Flush in Upland > Oil in the coolant or mixed coolant sludge? Route 66 Auto Repair in Upland flushes the block, radiator and heater core and refills with fresh coolant. Source: https://route66autorepairshop.com/cooling-heating-ac-services/cooling-system-flush Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** A full flush covers the **block and heater core**, not just the radiator. It follows a **contamination** diagnosis so the cleaning lasts. A cooling system flush cleans the whole loop: engine block, radiator, heater core, hoses and reservoir. Route 66 Auto Repair in Upland uses it when coolant is contaminated, for example with oil, rust, sludge from mixed coolant types, or stop-leak residue. We find the cause of the contamination first, because flushing a system that is still getting oil pushed into it just wastes your money. ## When does the whole cooling system need flushing? - Brown, milky or oily film in the reservoir - Thick gel from mixed coolant types - Stop-leak was used and the heater has gone weak - After a head gasket, oil cooler or transmission cooler failure - Rust-colored coolant that returns soon after a radiator-only flush ## Why is a full system flush different from a radiator flush? The radiator holds only part of the coolant. The engine block and heater core hold the rest, and they trap the heaviest deposits. A full flush uses repeated fills with cleaner and clean water, heater on, until every branch runs clear. On contaminated systems, we may replace the thermostat and cap too, since oil softens rubber seals. Oil in coolant has a source: an oil cooler, a head gasket or, on some vehicles, a [transmission cooler](https://route66autorepairshop.com/transmission-services/transmission-cooler-repair) inside the radiator. We test for that first and put the cause on the repair order. The refill has a published target as well. Most coolants are designed to run at about a 50/50 mix with water, which typically gives freeze protection down near 34 degrees below zero F and lifts the boiling point at the same time, and many makers allow a richer mix up to around 70/30 for extreme conditions. More coolant is not better past that point, since the water is what carries the heat away. The coolant type and mix listed for your vehicle are what go back in. ## Our cooling system flush process 1. **Find the cause:** We identify what contaminated the coolant and fix or quote that first. 2. **Clean in stages:** The system is filled with cleaner, run with the heater on, drained and repeated as needed. 3. **Rinse:** Clean water cycles run until the drain water comes out clear from every branch. 4. **Refill and verify:** Fresh coolant goes in at the right mix, air is bled, and heat and temperature are confirmed. ## What's included in a cooling system flush - Contamination check and cause noted on the repair order - Multi-stage cleaner and rinse cycles - Reservoir cleaning or replacement as quoted - Fresh coolant of the specified type - Air bleed with heater output check - Drain water photos, before and after ## Is it a need-now or need-later service? **Need now:** - Oil or sludge in the coolant - Overheating or no heat caused by deposits **Need later:** - Old but clean coolant, better served by routine service - Light discoloration with good protection readings ## How pricing and timing work A full flush takes more time and more coolant than routine service, and heavy contamination may need several cycles. The repair that caused the contamination is a separate line. The diagnostic fee is stated at the counter before testing and applies to approved related repair. For plain scheduled maintenance, [coolant system service](https://route66autorepairshop.com/cooling-heating-ac-services/coolant-system-service) is the lighter option. ## Aftercare Loosened deposits can settle. If the heater weakens again, the heater core may need its own [heater core flush](https://route66autorepairshop.com/cooling-heating-ac-services/heater-core-flush). Check the coolant color after a couple of weeks; any new film means we recheck the source first. ## Frequently asked questions ### Can a flush remove oil from the coolant for good? Only if the oil leak is fixed. Otherwise oil keeps coming back. That is why we confirm the source before cleaning. ### Will a flush unclog my heater core? It can help with loose deposits. A packed heater core may need a dedicated back-flush or replacement, which we explain before any extra work. ### Is a machine flush better than drain and fill? The method matters less than the result. We keep going until the water runs clear and the coolant tests right. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.