# Battery Terminal Inspection in Upland > Car clicks but the battery tests fine? Our Upland battery terminal inspection measures voltage drop across clamps and cables and records corrosion with photos. Source: https://route66autorepairshop.com/diagnostics-and-inspections/battery-terminal-inspection Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** We measure **voltage drop** across each clamp and cable during cranking and photograph **corrosion and loose connections** for your report. A battery terminal inspection at Route 66 Auto Repair in Upland checks the small connections that carry every amp to your starter and electrical system. A healthy battery cannot help if the clamp is corroded, loose or cracked. We measure how much voltage is lost across each terminal and cable while the engine cranks, photograph corrosion, and write down what needs cleaning or replacing. ## Signs your battery terminals need attention - A click or slow crank even though the battery was just tested good - White, blue or green crust on the posts or clamps - Dash lights flicker when you touch or wiggle the cable - The battery was replaced recently but starting trouble came back - A clamp that turns on the post by hand ## How do we test battery terminals? Looks can fool you. A clean-looking clamp can have corrosion hidden between the post and the clamp, and a crusty one can still pass current. So we test it. With a meter across the post and the clamp, and again across each end of the cable, we crank the engine and read how many volts are lost. A good connection loses very little. A poor one loses enough to make the starter click. We also check clamp tightness, look for cracked or spread clamps, and inspect the cable insulation for swelling. Corrosion can wick up inside the insulation, where it cannot be seen. Swelling or a stiff section near the clamp is a clue. The engine ground and the body ground get the same voltage drop check, because a bad ground acts just like a bad terminal. ## What the terminal report records - Voltage drop readings on the positive and negative sides - Engine and body ground readings - Clamp tightness and physical condition - Corrosion location, with photos - Cable insulation swelling or damage ## Our battery terminal inspection process 1. **Look and photograph:** We record corrosion, clamp condition and cable routing. 2. **Crank test:** Voltage drop is measured across each connection while cranking. 3. **Check grounds:** Engine and body ground paths get the same test. 4. **Report:** You get the readings and a recommendation to clean, repair or replace. ## What's included in a battery terminal inspection - Visual inspection with photos of corrosion - Voltage drop test on both battery cables - Ground path test - Clamp tightness and fit check - Cable insulation check - Written readings and recommendation ## Need-now or need-later? **Need now:** - A connection that drops enough voltage to cause a no-start - A cracked clamp or a cable burned near the terminal - A loose ground that makes lights and gauges act up **Need later:** - Light surface corrosion with passing voltage drop readings - Aging cable insulation with no swelling ## How pricing and timing work The fee is stated at the counter before we test. Cleaning a terminal is usually a small job. Replacing a cable depends on its length and how it is routed, which the written estimate shows before any work. If the car needs a tow-in because it will not start, we accept tow-ins and there is an after-hours key drop. AAA members save 10% on parts and labor, up to $75. ## What to read next Corrosion with good cables leads to [battery terminal cleaning](https://route66autorepairshop.com/electrical-services/battery-terminal-cleaning). Cracked clamps point to [battery terminal replacement](https://route66autorepairshop.com/electrical-services/battery-terminal-replacement), and damaged cables to [battery cable replacement](https://route66autorepairshop.com/electrical-services/battery-cable-replacement). If the battery itself is suspect, the [battery condition inspection](https://route66autorepairshop.com/diagnostics-and-inspections/battery-condition-inspection) load-tests it and reads its age. ## Frequently asked questions ### Why do my terminals keep corroding? Batteries vent small amounts of gas, and heat speeds that up. Overcharging can make it worse. If corrosion returns quickly after cleaning, we check the charging voltage too. ### Can I clean the terminals myself? Many drivers do. Disconnect the negative first, wear eye protection, and reconnect the negative last. If starting trouble continues after cleaning, the problem is likely inside the cable or clamp, which needs testing. ### Do you replace batteries and test my charging system? Yes. We sell and install batteries, load-test the old one, and can test the charging system so a new battery does not get drained by a weak alternator. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.