# Drive Shaft Inspection in Upland > Vibration at speed or a clunk into gear? Our Upland drive shaft inspection checks U-joints, center bearings and runout, then puts findings in writing. Source: https://route66autorepairshop.com/diagnostics-and-inspections/drive-shaft-inspection Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** We check **U-joints and the center bearing**, measure **runout** when vibration points there, and photograph what is worn. A drive shaft inspection at Route 66 Auto Repair in Upland checks the spinning shaft that carries power from the transmission to the rear axle on rear-wheel and four-wheel-drive vehicles. Worn U-joints, a tired center bearing or a bent tube cause vibration and clunks. We check each joint and support, measure runout when needed, and write up the findings with photos. ## When to have your drive shaft checked - A vibration through the floor that starts at a certain freeway speed - A clunk when you shift into drive or reverse - A squeak from under the car at low speed that follows wheel speed - A shudder when pulling away from a stop with a load - Rust dust or a missing grease cap at a U-joint ## How do we inspect a drive shaft? A U-joint, or universal joint, lets the shaft flex as the suspension moves. When its needle bearings wear, the joint gets loose or notchy. On the lift, we grip each side of every joint and twist and push in opposite directions. Any clunk or movement is recorded. Rust dust around the caps is a sign the bearings have run dry. Two-piece shafts have a center support bearing in a rubber mount; we check that rubber for cracks and sag. We look for missing balance weights and dents in the tube. If vibration is the complaint, we can measure runout, meaning wobble as the shaft turns, with a dial indicator. We also check the slip yoke at the transmission for play and the flange bolts for tightness. ## What goes on the drive shaft report? - Condition of each U-joint or CV joint on the shaft - Center support bearing and mount condition - Runout reading when vibration was the complaint - Missing balance weights or tube damage - Slip yoke play and flange bolt condition - Photos of worn joints or torn mounts ## Our drive shaft inspection process 1. **Road test:** We find the speed where vibration starts and listen for clunks. 2. **Joint check:** Each joint is twisted and pushed by hand on the lift. 3. **Support and tube check:** The center bearing, weights and tube are inspected. 4. **Measure and report:** Runout is measured if needed, and you get the written results. ## What's included in a drive shaft inspection - Road test for vibration and clunk - U-joint play check - Center support bearing check - Tube, balance weight and flange check - Runout measurement when vibration points there - Written findings with photos ## Need-now or need-later? **Need now:** - A U-joint with visible play or a clunk - A center bearing mount that has torn - Loose flange bolts **Need later:** - A dry U-joint that still turns smoothly, if it has a grease fitting - A slightly cracked center mount with no sag ## How pricing and timing work The counter tells you the inspection fee first. U-joint replacement is usually quicker than replacing a whole shaft, and the written estimate explains which we recommend and why. If balancing is needed, the estimate shows every step. Fleet trucks can have unit numbers added to invoices. AAA members save 10% on parts and labor, up to $75. ## Where to go next Worn joints lead to [U-joint replacement](https://route66autorepairshop.com/drivetrain-and-additional-mechanical-services/u-joint-replacement). A bent shaft or failed center bearing is covered under [driveshaft repair](https://route66autorepairshop.com/drivetrain-and-additional-mechanical-services/driveshaft-repair). Vibration can also come from the rear axle, which the [differential fluid inspection](https://route66autorepairshop.com/diagnostics-and-inspections/differential-fluid-inspection) helps rule out. Four-wheel-drive owners should see the [transfer case inspection](https://route66autorepairshop.com/diagnostics-and-inspections/transfer-case-inspection) too. ## Frequently asked questions ### What does a failing U-joint sound like? Often a squeak at low speed that follows the wheels, then a clunk when shifting. Left alone, it can turn into a vibration and eventually fail. ### Can a drive shaft vibration be tires instead? Yes. Tire balance problems are common and feel similar. The road test and a check of the tires help separate the two before any drive shaft part is ordered. ### What happens if a drive shaft fails? The vehicle loses drive to the rear wheels, and a loose shaft can damage the underside. That is why joints with play are marked need-now. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.