# Headlight Switch Replacement in Upland > Headlight switch replacement in Upland for lights that will not turn on, off or switch beams. We test the switch and circuit before you pay for parts. Source: https://route66autorepairshop.com/electrical-services/headlight-switch-replacement Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** A worn **switch or stalk** can cut headlights, high beams or dash lights. We prove it with **output testing** before ordering the part. Headlight switch replacement fixes the dash knob or steering column stalk that turns your lights on, switches beams and often runs the dash lighting. Route 66 Auto Repair in Upland replaces worn switches after testing proves the switch is the cause. Our ASE-certified technicians check what the switch sends, compare it to the wiring diagram, and give you a written estimate. If your vehicle needs setup or programming after the swap, that is confirmed on the estimate too. ## What are the signs of a bad headlight switch? - Lights that work only when the knob or stalk is held in one spot - High beams that will not switch on or will not switch off - Dash lights and headlights both acting up - Auto headlight mode that ignores darkness - A switch that feels loose, gritty or hot ## Knob, stalk or multifunction switch? Older cars often use a pull or rotary knob on the dash that carries lamp current directly, so its contacts wear and heat up. Most newer cars use a stalk on the steering column that sends a low-current signal to a module. That stalk may also run the turn signals and wipers, so it is called a multifunction switch. Because the switch shares a job with other parts, we check the [headlight relay](https://route66autorepairshop.com/electrical-services/headlight-relay-repair) and the module command before replacing it. Auto headlight faults can also come from a dirty light sensor on the dash, which is a quick fix. ## Our headlight switch replacement process 1. **Test each position:** We work the switch through every position and record which lamps respond. 2. **Measure switch output:** A meter or scan tool shows whether the switch sends the right signal for each position. 3. **Replace the switch:** Trim, column covers or the airbag area are handled per service procedures, and the new switch is installed. 4. **Set up and verify:** Any required setup is done, then all lamps, dash lighting and related stalk functions are checked. ## What's included in a headlight switch replacement - Position-by-position switch test - Output or scan data check for the lighting command - Switch replacement with trim reinstalled - Any required setup, listed on the estimate - Check of headlights, dash lights, signals and wipers where shared ## Can a bad headlight switch wait? **Need now:** - Headlights that cut out while driving - A switch that is hot to the touch - No way to turn on low beams **Need later:** - Auto mode not working while manual mode works - Dash dimmer control that is stuck at one level - A loose stalk that still works in every position ## How pricing and timing work Switch prices vary widely: a simple dash knob costs far less than a multifunction column switch. The diagnostic fee is stated at the counter before testing and is applied to the approved related repair. Parts availability sets the timing, and we text you if a switch has to be ordered. AAA members save 10% on parts and labor, up to $75, when they show the card at time of service. ## Aftercare Use the switch normally; there is no break-in. If lights act up in one position later, call [(909) 608-7699](tel:+19096087699). For flicker in only one lamp, the cause is more likely in the [headlight wiring](https://route66autorepairshop.com/electrical-services/headlight-wiring-repair), and our [electrical system diagnostics](https://route66autorepairshop.com/electrical-services/electrical-system-diagnostics) page explains how we handle faults that come and go. ## Frequently asked questions ### Why did my turn signals stop working along with the high beams? On many cars the same stalk handles both, so a worn multifunction switch can affect both. We test each function before quoting the switch, because a shared fuse or module can also cause it. ### Is there an airbag near the switch? On column-mounted switches, yes. Technicians follow the service procedure for disabling and restoring the airbag system before removing covers, and check for warning lights afterward. ### Can I buy the switch myself? You can. We inspect customer-supplied parts before installing them. There is no warranty on the part itself, and labor is still charged at book time. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.