# Engine Oil Cooler Hose Repair in Upland > Leaking or chafed oil cooler lines? Route 66 Auto Repair in Upland replaces oil cooler hoses and fittings and checks the routing so it does not happen again. Source: https://route66autorepairshop.com/oil-change-services/engine-oil-cooler-hose-repair Updated: 2026-09-17 Business: Route 66 Auto Repair, 1775 W Foothill Blvd, Upland, CA 91786, (909) 608-7699 Hours: Monday to Friday 8 AM–5 PM, Saturday 8 AM–2 PM, Sunday closed **TLDR:** Leaking **oil cooler hoses** can empty an engine quickly. We replace the failed line, fix the **routing and clips**, and refill before a road test. Oil cooler hoses carry hot, pressurized oil between the engine and a front-mounted cooler. Route 66 Auto Repair in Upland replaces cooler hoses and lines that are cracked, chafed, rusted at the crimps or leaking at the fittings. These lines hold real pressure, so a small weep can turn into a sudden loss of oil. We trace the full run from engine to cooler, photograph the failure point, and explain what is causing it before you approve the repair. ## Where do oil cooler hoses fail? Most cooler lines are a mix of rubber hose and metal tube joined by crimped ferrules. The rubber ages from heat. The crimps rust, especially on trucks that see road salt or coastal air before landing in the Inland Empire. Lines that lost a support clip rub on the frame or the radiator until they wear through. Fittings can also leak when an O-ring hardens. On some trucks, the line is one assembly, so a single bad section means replacing the full line. The same chafing shows up on [transmission cooler lines](https://route66autorepairshop.com/transmission-services/transmission-cooler-line-repair), so we glance at those while we are there. ## Signs your oil cooler lines are leaking - Oil sprayed across the front of the engine or the radiator - A puddle under the front bumper rather than under the engine - Wet, swollen rubber near a crimp or fitting - Shiny rub marks on a line where a clip used to be - A low oil warning after a hard pull or a towing run ## Our oil cooler hose repair process 1. **Trace the run:** We follow the lines from the engine to the cooler and photograph every leak and rub point. 2. **Quote the right part:** Your estimate shows whether a hose section, a fitting seal or a complete line assembly is needed. 3. **Replace and secure:** We install the new line, new O-rings and any missing clips so it cannot chafe again. 4. **Refill and test:** Oil is topped off or changed, the engine is run, and the lines are checked under pressure and on a road test. ## What's included in an oil cooler hose repair - Full-length line inspection with photos - Replacement hose or line assembly as quoted - New fitting O-rings and support clips - Oil top-off or change - Running leak check and road test ## Is it a need-now or need-later repair? **Need now:** - Any active drip or spray from a cooler line - A line worn through the outer layer at a rub point - A low oil pressure or low oil level warning **Need later:** - Surface rust on crimps with no weeping - A missing clip on a line that has not yet rubbed ## How pricing and timing work Price follows the part design and access. Some lines are sold only as full assemblies, and some need the radiator or a skid plate moved. Parts availability can change timing, and we text you if the look window slips. If the leak turns out to be at the cooler itself, we stop and quote [engine oil cooler repair](https://route66autorepairshop.com/oil-change-services/engine-oil-cooler-repair). If a regular [oil change](https://route66autorepairshop.com/oil-change-services/oil-change) is close, we can combine the two. Fleet vehicles get unit numbers on the invoice. Call [(909) 608-7699](tel:+19096087699). ## Frequently asked questions ### Can I drive with a leaking oil cooler line? It is not worth the risk. These lines are under pressure and can fail all at once, which can drain the engine in minutes. If the leak is active, we recommend a tow. We accept tow-ins and have an after-hours key drop. ### Can you just patch the hose? No. Oil cooler lines see heat and pressure that patches and hose clamps cannot hold reliably. We replace the failed section or assembly with parts built for that pressure. ### Why did my new line fail again? Usually because the cause was not fixed: a missing clip, a rubbing edge, or a hose routed too close to the exhaust. We check routing on every job. If a repair of ours comes back, it goes to the front of the line and the root cause goes on the repair order. --- Call (909) 608-7699 or visit https://route66autorepairshop.com/contact for a written estimate.